Remote controlling a PC on the local networkĢ. ![]() Got 2 flex mini working this way.įound a way to do this “completely remote” as the switches were already installed at the customer and I realized afterwards that I should have pre-configured the switches with the inform/host address from a network with a USG connected to my remote controller. Pushed the changes and then moved the switch to where I wanted it in the house. I was able up adopt it update it change any settings I wanted. Copy the result remove the 0x and add 0104 to the beginning.ĥ) save everything and start the server service and set the firewall settings or turn off the firewall.Ħ) Boot the switch and plug in the cable to the PC’s Ethernet port to Get an address assigned.ħ) Unplugged the switch from My PC and Plugged a second cable from the router into the flex mini.Ĩ) The flex mini then showed up on the controller ready for adoption. Went to to convert the IP address of my controller to hex. I also set the gateway and dns option to point to the routers IP.Ĥ) set dhcp option 43. This also was not straight forward for me because my fiber gateway router from the provider does not have this option.ġ) I ended up downloading windows DHCP from I used an old version that was provided free.Ģ) set a static IP on my Ethernet port that is in the same subnet as my router.ģ) set up the DHCP server to only serve a few address outside of what the router provided ie. I had a difficult time none of the methods worked for me that were listed above. Till now I haven’t had a need to setup those additional settings since I would SSH into the device and manually set the inform, so now that those settings are configured I might need to do the manual setting of the inform on new devices that I get for my network. Then is showed up to be able to be adopted in my controller. Wait for a few minutes and goto the devices screen, or refresh if already have the devices screen up.ġ1. Put the USW Flex Mini in recovery mode as mentioned in this article while not connected to the switch.ġ0. Set “DHCP UniFi Controller” to my controller’s IP Address.Ĩ. Set “Host for Inform” to my controller’s IP Address.Ħ. Goto Settings -> System Settings -> Controller ConfigurationĢ. This was also after updating to controller version 6.2.25ġ. I had to go through some extra steps to get mine to show up in my controller which is hosted on an AWS EC2 machine. Here is a Video to help you out if you need it. Once adopted, upgrade the firmware if needed.Open the controller and you should now see the device.This will put the device into recovery mode ![]() hold the reset button down on the USW-Flex-Mini until the light flashes white and blue.plug the USW-Flex-Mini in a port on the main switch that is on the main LAN network.Here are the steps we had to take to get the USW-Flex-Mini to adopt on a remote controller. This turned out to be an issue and I was called in to help. Within minutes, he noticed there was no SSH server on the mini and since the controller was in the cloud, it wasn’t showing up for adoption in the controller. This is a simple install, no hard SSH commands so we decided to send a young tech out to have his first solo install done. We could power it with POE, link it back to his core switch and have his devices in his office hard wired (some of them can’t be on wifi). After doing some research for his needs, we came to the conclusion that the flex mini was the best choice. ![]() The challenge was we couldn’t run a new cable and the home owner didn’t want to spend a lot of money as this was for his home office. For MSPs or tech enthusiates, this brings on unique challenges with some of the new products unifi is deploying.įor us, recently we installed a USW-Flex-Mini in a home that only had 1 ethernet port but needed more. With recent changes to unifi, a lot of their push seems to be to not have controllers “in the cloud” but for you to buy a controller or a pro device with the controller built in. This allows all your customers devices to report back to a simple dashboard for you to manage. The most common use case for this is to have a unifi controller “in the cloud”. MSP’s like ourselves love the ability to manage remote networks for our clients. The unifi line is becoming more and more popular as the months go by.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |